Life-fitness G3 Uživatelský manuál

G3 GYM SYSTEMASSEMBLY INSTRUCTIONSG3-001 / CLASS H / 09/19/08 / 8600401 / REV B-2

931CABLING DIAGRAM 4

1030CABLING DIAGRAM 5

11STEP 1:• Loosely assemble two BASE PLATES (11) to the FRONT BASE (1) and the BASE CONNECTOR(3) using four 3/8 x 3-3/4" BOLTS (57) and four 3/8&

12STEP 2:• Loosely assemble the RIGHT ARM (5) and REAR BASE (4) using two 3/8 x 3-3/4" BOLTS (57),two 3/8" WASHERS (64) and two 3/8" SI

132123FIGURE 4FIGURE 3Make sure that the WEIGHT PLATES (21) are assembled as shown in Figure 3 and the HEADPLATE ASSEMBLY (23) is assembled as shown i

14STEP 5:• Place the GUIDE RODS (18) through the BOTTOM SHROUD BRACKET and into the REARBASE (4) as shown in Figure 5.• Lubricate the GUIDE RODS (18)

15STEP 6:A. Swing the GUIDE RODS (18) into the guide rod bushings in the RIGHT BOOM PLATE (14) andLEFT BOOM PLATE (15) as shown in Figure 6.B. Loosely

16STEP8:• Securely assemble the FIVE PRONG KNOB (43) to the FRONT BASE (1) as shown.• Insert the SEAT ADJUST (7) into the FRONT BASE (1) as shown. The

17STEP9:• Detach the Short Cable from both REAR GUIDE CABLES (74) as shown in Figure 9 (B).• Slide the Long Cables of the REAR GUIDE CABLES (74) throu

18IMPORTANT! UNCOIL AND STRAIGHTEN ALL CABLES TO REMOVE ALL TWISTS BEFOREINSTALLING.STEP 10:• Assemble the WEIGHT STACK PIN (27) tothe HEAD PLATE ASSE

TABLE OF CONTENTSSafety Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19STEP 11:• Loop the WEIGHT STACK CABLE (29) around one 3-1/2" PULLEY (37). • Assemble the 3-1/2" PULLEY (37) with the WEIGHT STACK CABLE (2

20STEP 12:• Loop the BOOM CABLE (32) around one 3-1/2" PULLEY (37).• Assemble the 3-1/2" PULLEY (37) with the BOOM CABLE (32) looped around

21STEP 13:• Securely assemble the ball end of the LEG CABLE (30) and one 3-1/2" PULLEY (37) to the LEGPEDESTAL (8), using one 3/8 x 3-3/4" B

22FIGURE 14STEP 14:• Securely assemble one 3-1/2"PULLEY (37) to the PULLEYPLATES (10), using one 3/8 x 1-3/4"BOLT (53) and one 3/8" SIL

23STEP 16:• Route the ARM CABLE (31) through the LEFT ARM (6) as shown in Figure 16.• Loop the ARM CABLE (31) around one 4-1/2" PULLEY (38).• Sec

24STEP 17:• Securely assemble two 3-1/2" PULLEYS (37) to the BASE PLATES (11), using two 3/8 x 3-3/4"BOLTS (57), one 3/8 x 1" SPACER (5

25STEP 18:• Route the ARM CABLE (31) through the RIGHT ARM (5) as shown in Figure 18.• Loop the ARM CABLE (31) around one 4-1/2" PULLEY (38).• Se

26STEP 19:• Insert the ARM CABLE (31) ends through the SWIVEL PULLEY ASSEMBLIES (72).• Insert the SWIVEL PULLEY ASSEMBLIES (72) into the LEFT ARM (6)

27STEP 21:• Assemble two ROLLER PADS (17) to the LEG PEDESTAL (8) using one 3/4 x 18" TUBE (24),four PLASTIC WASHERS (45), two ROLLER PAD CAPS (4

28STEP 22:• Make adjustments to the cables’ tension at the locations shown in Figure 22.• Adjust the Turnbuckle on each GUARD CABLE (65) to change the

INSPECTION1 DO NOT use or permit use of any equipment that is damaged and or has worn or broken parts. For all LIFEFITNESS equipment use only replacem

29STEP 23:• SECURELY assemble the TOP SHROUD BRACKET (3) to the RIGHT and LEFT BOOM PLATESusing two 3/8 X 2-1/2” BOLTS (7) and two 3/8” SILVER LOCK NU

30This completes the assembly of the G3 Gym System. STEP 24:A. SECURELY assemble the LEFT SHROUD (1) and RIGHT SHROUD (2) to the TOP (3) andBOTTOM (4)

MAINTENANCEOWe recommend cleaning your product (pads and frame) on a regular basis, using warmsoapy water. Touch-up paint can be purchased from your L

32WARRANTYLife Fitness extends the following LIMITED WARRANTY to the original owner of the Life Fitness products. The Warrantyterms apply to IN HOME U

33CORPORATE HEADQUARTERS5100 North River RoadSchiller Park, Illinois 60176 • U.S.A.847.288.3300 • FAX: 847.288.3703800.735.3867 (Toll-free within U.S.

IMPORTANT NOTESThank you for purchasing the Life Fitness G3 Gym System. Please read these instructions thor-oughly and keep them for future reference.

4G3 FOOTPRINT1 SQUARE = 1' X 1'MAXIMUM USER WEIGHT:300 lbs (136 kg)MINIMUMREQUIRED USABLE SPACE:Length = 90 inches (229 cm) 7' 6"W

5PARTS LISTNOTE: Some of the components may be pre-assembled.1 FRONT BASE 12 UPRIGHT 13 BASE CONNECTOR 14 REAR BASE 15 RIGHT ARM 16 LEFT ARM 17 SEAT A

6CABLE END ASSEMBLY:Slide parts onto cable in the following order: Item 2, Item 4, Item 3.Insert cable end into Item 1.Slide entire assembly over Item

729CABLING DIAGRAM 2

832CABLING DIAGRAM 3